Why should I have my chimney inspected?
According to the National Fire Protection Association, chimneys should be inspected or cleaned annually. The chimney and fireplace / furnace system is quite complicated and an inspection can alert you to a potential problem before it becomes a costly repair or a safety issue. Many times homeowners are unaware of problems that may exist. There are 3 levels of chimney inspections that can be done depending on each individual case. It is always a good idea to schedule your inspection and cleaning in the late summer or early fall, before you begin using the chimney or furnace during the heating season. Another important time to have an inspection is if you have just purchased the home and want to be sure about the condition of the chimney system.
How does a Chimney Sweep clean a chimney? Will it make a mess?
We put down clean floor coverings around your fireplace and always clean up all work areas. Our specialized tools and powerful vacuums will prevent 99% of soot or dust from entering your home. The chimney is always cleaned from the bottom, reaching the firebox, smoke chamber, damper, smoke shelf, and flue liner.
Our qualified technicians are more than just Chimney Sweeps, they are fully trained at diagnosing potential problem areas in your Chimney and Venting System. If we see something that is not right, we will notify you and perform a more detailed inspection if necessary. We never do any repairs or work without the customers permission, but it is our duty to report on any deficiencies in the system. We advise that customers go ahead and have a full annual level one inspection along with their cleaning just to stay on top of any maintenance or safety issues that may be present.
What is Creosote, how does it get in the chimney and why is it dangerous?
The Chimney Safety Institute of America (CSIA) recommends that masonry chimneys should be cleaned when ¼ inch of sooty build-up and creosote is present. Factory built insert fireplaces can actually become a hazard with a much thinner build-up on the inside walls. Either type can reach a dangerous level after burning as little as a cord of wood, so your cleaning schedule may end up being 1 or 2 times per year. Even if you don’t use your chimney much, there is always the chance that animals have built nests during the summer that can form a blockage or things like leaves can accumulate during the fall.
Natural gas is cleaner than wood, but the fumes actually create more water vapor than wood burning fires. This means more condensation in the chloride containing fumes, which can create a hydrochloric acid coating on the furnace flues. This is a highly corrosive agent and these systems should be checked at least once a year.
How often should I have my chimney or furnace flues cleaned?
The answer to this question depends on what fuel you use. It also depends on the age of your home, the condition of your chimney, and the weather (mild winters cause more problems than cold ones!). Generally, if you use wood, it’s good to have the chimney cleaned at least every 12 months (more often if you burn two or more cords of wood, or if you burn green wood). Oil flues - especially if there’s a ventilation problem - need to be inspected and cleaned each year in order to avoid chimney blockage. Problems in the furnace or boiler can cause highly sooty conditions in the chimney. Even though natural gas is a clean-burning fuel, today’s high-efficiency gas furnaces create special problems. The fumes they produce are cooler and produce higher levels of water vapor than previous models, and this vapor in turn produces more water condensation. These vapors also contain chlorides from house-supplied combustion air which combine to form hydrochloric acid. The acid-water condensates from these latest natural gas furnaces cause more flue deterioration than previous models. It’s important to check the chimneys that vent these systems at least once each year.
How long does chimney cleaning usually take?
Many of our chimney cleanings also include time to do a top to bottom, inside and outside level one inspection as well, so time on those appointments varies. A typical chimney cleaning alone should be able to be finished in an hour.
Should I be concerned about Carbon Monoxide poisoning?
Carbon monoxide is produced whenever gas, oil, kerosene, wood or charcoal is burned. Higher levels can be produced when your chimney is not functioning properly. This odorless gas can accumulate to dangerous levels when a blocked chimney or flue prevents the gases from properly venting out and away from the home. Hundreds die needlessly every year because of undetected problems with fuel burning appliances, stoves or fireplaces. Flues should be inspected routinely for rust, blockage and defects that may allow gases to back draft into the home.
Symptoms of Carbon Monoxide poisoning are headaches, nausea and fatigue. You should always have detectors installed in your home to guard against unsafe levels of this odorless, colorless gas. But don’t just rely on the detectors, make sure that your venting systems are inspected and in good working order at all times.
Do I need to be home all day to wait for the Chimney Cleaning?
We always strive to be prompt and on-time. Since we are able to schedule appointments starting at 8 am, through to our last appointment at 3:00 pm you should be able to find a time when it will be convenient for you. There is also an opportunity to have work done on week-ends if necessary.
What is Chimney Relining? Do all chimneys need liners?
Traditionally, masonry chimneys had clay tiles that covered the inside of the chimney. These tiles were designed to seal the chimney structure and direct all the sparks, heat, gases and particles up and out of the home. The problem is that over time, the tiles crack or break due to weathering, heat and freeze cycles, and other factors. Once the break-down begins, your chimney can become dangerous to use and can require a new lining. Some older chimneys did not even have the tile liners, so they are a real hazard that needs immediate attention. Chimneys built before 1940 have a high likelihood that they were built without a clay liner. Every chimney needs a liner of some kind that is designed to fit the needs of the fireplace, stove or furnace that is venting through it.
There are many solutions to relining a chimney, the most popular being a stainless steel liner being installed in the chimney space from top to bottom. This flue can also be insulated to increase efficiency and needs to be fitted properly to the chimney using flexible or rigid flue piping.
Do I really need a Chimney Cap?
Your chimney cap closed the door on excess water entering your chimney and the damage that it causes. It also keeps out birds, squirrels, raccoons and other critters that may think your chimney looks like a good summer home. A very common problem is when raccoons, squirrels, birds and bats try to make their home in your chimney. They can block proper ventilation and even enter your home, potentially spreading disease and wreaking havoc. Our strong mesh and caps will keep even the most determined critters out!
Leaves and other debris that storms and high winds can blow into your chimney are blocked out too. Blockages that occur from these causes are often the fuel for dangerous chimney fires. The chimney cap (or guard) protects the home of the risk that sparks and airborne embers will land on your roof, causing a fire hazard.
Prefab Fireplace Inserts – can they be repaired or replaced?
Many newer homes have a factory built fireplace that is installed in the wall with a framed wall outside the home that contains the venting system. These fireplaces are usually constructed using galvanized steel and last from 20 to 30 years on average. If you see gaps or cracks in the walls of your firebox area, rust or warped panels – you need to have the system inspected and possibly repaired. If the prefab fireplace insert has reached its limit for use, we can also install a new fireplace insert that can fit right into the existing space. This does require extensive carpentry work in addition to the new fireplace insert, but it can be done with minimal intrusion to the home in a relatively short amount of time.
Why is water leaking into and around my fireplace, or staining the ceilings?
Water is the major enemy of your fireplace system. It can seep in many places, cracking and corroding joints, mortar and brick. Excess condensation caused by improper operating flue systems adds water to your chimney. Cracks can let water in, un-capped chimneys invite water damage and defective flashing can allow roof leaks.
At the first sign of water, have an inspection! You will end up saving money and hopefully put an end to any potentially unsafe conditions. Many times if the problem is caught early – the cost to repair is much less than a future cost to replace.
Why does my chimney smell, especially during the spring and summer?
The culprit that smells up your home through your chimney is creosote. As you read above, creosote is a natural by-product of burning fuel, especially wood. When the weather is humid and warm, the creosote odor gets stronger. Of course, chimney cleaning will resolve much of the smelly chimney problem, but not always completely. Odor neutralizing agents like baking soda or kitty litter put into the fireplace can help, but many times a deodorizing agent needs to be spread into the chimney.
Sometimes ventilation fans can be installed to reduce these problems. The fact that you have these odors may also indicate that your venting system is drawing too much air down the chimney (downdraft) or that your damper may be defective. There are also several structural defects that can show up as a smelly chimney, so as always we advise a thorough inspection to determine the root cause.
My fireplace smokes, can anything be done about that?
Smoke coming into your home is certainly not enjoyable and indicates a problem with a poor draw up and out of the chimney. Smoke may also escape through leaks in your liner into other areas of the house. If you smell smoke in other rooms, your problem is likely with your liner. Remember, your liner must be the correct size for the fireplace, stove or furnace that your are venting – if it is not, the gases and smoke will not all escape the home. If your damper is not working properly or is closed you will also get smoke back drafting into the home. Many of today’s homes are built very tight, so the air that is taken out of the room during burning can’t be replaced. Outside air needs to be introduced in order to remedy the imbalance and allow the smoke to be drafted out of the chimney. If your smoking problem goes away when you crack open a window, this may be your problem. If you have smoke in your home when you use your fireplace, it is not a safe situation.
What is that whitish discoloration on the outside of my chimney?
This deposit is called efflorescence. When gases leak out through a defective liner and onto your brick interior wall they deposit salts on the surface of the masonry. Water then dissolves and transports these salts through the joints and mortar to the exterior of the chimney where you see the white deposits. So these are the telltale signs of leaks in your liner and water problems in your chimney system. Repairs should be made immediately to prevent further deterioration of your chimney.